Everlast Welders Canada PowerPlasma 62i 60 Amp Review: Specs, Pros and Cons

What stands out

• 60 Amp inverter output with a 60% duty cycle
• Severs up to 1 1/4-inch thick material
• CNC compatible for automated cutting setups
• 3-second pilot arc tip saver feature
• Digital display for adjustable postflow timer

Who it fits

Key specs for the PowerPlasma 60

60 Amp Inverter Type cutter

This rating indicates the maximum electrical current the machine can output during operation. Higher amperage allows you to cut thicker materials with greater ease and speed. You should compare this figure against other plasma cuters to ensure it meets your typical material thickness needs. An inverter type design also generally offers better efficiency and a lighter form factor than older transformer-based models.

60% duty cycle

This specification tells you how long the machine can run continuously at full power within a ten-minute period before it must cool down. A sixty percent duty cycle means you can cut for six minutes straight, followed by four minutes of rest. This is practical for medium to heavy industrial tasks. You should check this number against your intended workload to avoid overheating during extended cutting sessions.

Regularly Cutting 3/4"

This value represents the thickness of steel the unit can handle in standard, daily operations. It suggests the machine is optimized for materials up to three-quarter inch thick. You can rely on this capability for most fabrication jobs without straining the equipment. When shopping, compare this limit with your most frequent cutting requirements to ensure the tool matches your regular production volume and material specs.

Maximum up to 1 1/4" severance cut

This figure indicates the absolute maximum thickness the plasma cutter can slice through, though likely at slower speeds or reduced quality. It provides a safety margin for occasional thicker material needs. You should understand that this is not for daily use but for specific severance tasks. Compare this maximum limit with other models to see if it offers the extra capacity you might need for emergency or heavy-duty separation work.

Design and build overview

According to the listing, this unit employs IGBT Infineon modules and inverter technology. This electronic architecture typically allows for a more compact chassis than older transformer designs. You get a lighter, more portable machine that fits easily into a workshop or job site truck. The compact form factor supports its CNC compatibility, meaning you can mount it on automated cutting tables without excessive footprint constraints.

The torch assembly is a Blow Back IPT-60 plasma torch. This specific torch design is rated for the machine’s 60-amp output. It connects directly to the power source, requiring you to manage hose routing carefully. The digital display on the control panel shows the adjustable postflow timer setting. This visual feedback helps you monitor gas usage, which extends consumable life. You can tweak this setting to match your cutting speed and material thickness.

The unit is built to handle regular cuts through 3/4-inch steel and severance cuts up to 1 1/4-inch. This capacity dictates the physical robustness of the internal components. The machine is suitable for use with 11,000-watt clean power generators. This specification suggests a durable electrical system that can withstand the voltage fluctuations common on remote job sites. You do not need a dedicated industrial power line to operate it, provided your generator meets the stated wattage. The design prioritizes field usability alongside workshop precision.

Setup and daily operation guide

You begin setup by connecting the PowerPlasma 60 to a suitable power source. The listing notes it works with 11,000-watt generators, which helps if you need mobility. You attach the included Blow Back IPT-60 plasma torch to the front panel. This torch is the primary interface for your cutting tasks. Once powered, you adjust the settings on the digital display. This screen controls the adjustable postflow timer. This feature extends the life of your consumables by keeping the gas flowing after you lift the torch. It also simplifies routine maintenance for you.

During daily use, the machine relies on a 3-second pilot arc tip saver. If you do not initiate a cut within three seconds, the system shuts down the pilot arc. This prevents premature wear on your consumables when the torch is idle. You benefit from this protection without needing to monitor the timer manually. The unit operates at a 60% duty cycle at 60 amps. This means you can cut regularly through 3/4-inch steel for extended periods. For thicker materials, you can achieve severance cuts up to 1 1/4-inch. The CNC compatibility allows you to integrate this cutter into automated systems. You simply connect the control signals from your CNC machine to the plasma cutter’s interface. The inverter technology ensures stable output during these operations. You get consistent plasma arcs for clean cuts. The digital display keeps you informed of your current settings. This setup supports both manual handheld cutting and automated CNC workflows efficiently.

Before You Buy This Plasma Cutter

Before you commit to this Everlast unit, verify your workspace compatibility. The listing confirms CNC compatibility, so ensure your plasma table accepts standard torch interfaces and has adequate air pressure regulation. You will need a clean, dry air supply to maintain cut quality and extend consumable life. Check that your generator can sustain 11,000 watts if you plan to move the machine off-site. The included Blow Back IPT-60 torch is a solid starting point, but you may want spare tips and electrodes for regular maintenance. This model sits as a heavy-duty option in our 1 reviews, best suited for those needing frequent 3/4-inch cuts or occasional severance work up to 1 1/4 inches. Unlike lighter duty cutters, this inverter-based system requires proper ventilation due to its high amperage output. Keep the digital postflow timer set correctly to protect the nozzle during shutdown. If you need portability without sacrificing thickness capacity, this fits your workflow.

Check before you buy

• Verify CNC table torch interface compatibility
• Confirm generator supports 11,000 watts
• Check air pressure and cleanliness requirements
• Ensure adequate workshop ventilation

The product at a glance

1

Everlast PowerPlasma 60-Amp Plasma Cutter

Best for: CNC compatible 60 amp cutting up to 1 1/4 inch

Features

Plasma Cutter

View on Amazon: Everlast PowerPlasma 60-Amp Plasma Cutter Affiliate link

The Everlast PowerPlasma 62i is a 60-amp inverter plasma cutter built for CNC compatibility and regular shop use. It delivers a 60% duty cycle and cuts up to 1 1/4 inches. The unit includes a Blow Back IPT-60 torch and features a digital postflow timer. It also offers a 3-second pilot arc tip saver to extend consumable life. You can run it on clean power generators for field work.

Pros

• 60 amp inverter output with 60% duty cycle
• Cuts up to 1 1/4 inch severance thickness
• Digital adjustable postflow timer display
• 3-second pilot arc tip saver feature
• Compatible with 11,000 W clean power generators

Cons

• 60% duty cycle limits continuous heavy industrial use
• No Bluetooth or smart app connectivity listed
• No remote control included for torch operation

Good fit if

• You need a CNC compatible plasma cutter for shop work
• You require a 60 amp machine for up to 1 1/4 inch cuts
• You want a unit that works with clean power generators

Skip if

• You need to cut materials thicker than 1 1/4 inch
• You require a duty cycle higher than 60% for continuous use
• You want a machine with smart app connectivity

Verdict: Everlast PowerPlasma 62i 60 Amp Cutter fits fabricators who need reliable CNC compatibility and a 60 amp duty cycle for moderate thickness metal. It suits users who value digital controls and generator compatibility over smart features.

Specifications side by side

Frequently asked questions

See also

• everlast welders canada powerplasma 62i 60 amp alternatives
• best everlast welders canada TIG welders
• king canada 10 15 amp sliding review
• sonos amp review